Ankersmid heated line series
AHLH2505-BR
For ultra-high temperatures
up to 250°C
Stainless steel tube
(6x1, 8x1 or 10x1 mm)
Application
This electrical heated AHLH2505-BR sample tube is designed to connect to all Ankersmid sample elements. They are used to keep the necessary gas components above their ACID-dew point, and avoid condensation.
This is a safe way to transport the sample to a heated analyser or the special Ankersmid coolers.
Description
Fixed sample tube out of stainless steel.
These AHLH2505-BR heated lines are manu-factured according to the clients needs and completely confectioned in the factory at a fixed length.
The sample line is standard equipped with a PT100 for temperature control. The heater used in this type is ONE serial resistance, twisted around the tube. Due to this construction we can not have cold zones or spots, where a potential blockage can occur.
Flexible isolation out of multi-layer glass wool
A variety of standard lines is available but many options can be supplied as well.
Ready-to-use with multi-pole connector.
See our code page Chpt. 2.1.1 for all versions.
· Completely manufactured “ready-to-use”
· ONE serial heater
· Never cold spots
· Tube 6x1 , 8x1 or 10x1 mm
· Integrated PT100 (other sensors on request)
· External temperature controller required
· Fixed stainless steel tube
Schematic picture
L Total length
DA Outside diameter of inner tube
DK Silicon end connection outside diameter
DM Polyamide braided jacket outside diameter
LA Length of connection stud
LK Length of silicon end connection
LL Length of cable connection
|
DN |
6x1 |
8x1 |
10x1 |
|
DA |
6 mm |
8 mm |
10 mm |
|
DK |
48 mm |
|
|
DM |
42 mm |
|
|
LA |
25 mm |
|
LK |
110 mm |
105 mm |
|
LD |
64 mm |
|
LE |
35 mm |
|
Min. bending radius |
160 mm |
Maximum operating temperatures and power consumption
|
Tmax |
Sample tube |
6x1 mm |
8x1 mm |
10x1 mm |
|
250°C |
Fixed |
125 W/m |
125 W/m |
125 W/m |
|
250°C |
Interchangeable |
125 W/m |
150 W/m |
150 W/m |
(Tolerance on power: 10% between -20°C and +40°C)
Maximum available lengths for power connection 230 VAC and 115 VAC
|
Tmax |
Power |
6x1 mm |
8x1 mm |
10x1 mm |
|
250°C |
230 VAC |
41 |
41 |
41 |
|
250°C |
115 VAC |
20 |
20 |
20 |
(Tolerance in length: 2%)
Ankersmid purchase codes (extraction, see code page Chapter 2.1.1 for all available versions)
|
Sample line
version |
Power
supply |
Outer
diameter |
Description
code |
Length code x (meter) |
Beginning and end fitting (1x) |
|
PTFE-tube
Fixed
Max. 250°C |
230VAC |
6 mm |
AHLH2503-BR06-230P |
AHL053 |
AHL503 |
|
230VAC |
8 mm |
AHLH2503-BR08-230P |
AHL054 |
AHL504 |
|
230VAC |
10 mm |
AHLH2503-BR10-230P |
AHL055 |
AHL505 |
|
PTFE-tube interchangeable
Max. 250°C |
230VAC |
6 mm |
AHLH2504-BR06-230P |
AHL059 |
AHL509 |
|
230VAC |
8 mm |
AHLH2504-BR08-230P |
AHL060 |
AHL600 |
|
230VAC |
10 mm |
AHLH2504-BR10-230P |
AHL061 |
AHL601 |
|
Stainless steel tube
Max. 250°C |
230VAC |
6 mm |
AHLH2505-BR06-230P |
AHL064 |
AHL604 |
|
230VAC |
8 mm |
AHLH2505-BR08-230P |
AHL065 |
AHL605 |
|
230VAC |
10 mm |
On request |
|
PTFE-tube
Fixed
Max. 250°C |
115VAC |
6 mm |
AHLH2503-BR06-115P |
AHL081 |
AHL801 |
|
115VAC |
8 mm |
AHLH2503-BR08-115P |
AHL082 |
AHL802 |
|
115VAC |
10 mm |
AHLH2503-BR10-115P |
AHL083 |
AHL803 |
|
PTFE-tube interchangeable
Max. 250°C |
115VAC |
6 mm |
AHLH2504-BR06-115P |
AHL087 |
AHL807 |
|
115VAC |
8 mm |
AHLH2504-BR08-115P |
AHL088 |
AHL808 |
|
115VAC |
10 mm |
AHLH2504-BR10-115P |
AHL089 |
AHL809 |
|
Stainless steel tube
Max. 250°C |
115VAC |
6 mm |
AHLH2505-BR06-115P |
AHL092 |
AHL902 |
|
115VAC |
8 mm |
AHLH2505-BR08-115P |
AHL093 |
AHL903 |
|
115VAC |
10 mm |
On request |
Example: AHLH2503-BR06-230P
Coding:
AHL: Ankersmid Sampling, Heated Line
H: Higher temperature
250: Maximum regulated setpoint 250°C
3: Fixed PTFE-tube with SS stud
BR: Outer polyamide braided jacked with red silicone insulation (>200°C)
06: Outside tube diameter 6mm
230: Supply 230VAC
P: PT100 2-wire version